
Electrical cable assemblies and wire harnesses
Electrical cable assemblies and wire harnesses
Bundles of wires and connectors that carry power and signals between the parts of a system, built to IPC/WHMA-A-620.
Bundles of wires and connectors that carry power and signals between the parts of a system, built to IPC/WHMA-A-620.
What is a wire harness?
What is a wire harness?
A wire harness is a group of wires, cables, and connectors bundled and routed as one unit, so a system can be wired in one step instead of wire by wire. An electrical cable assembly is similar but usually built around a single cable with connectors on each end. Both carry power and signals between the parts of a system.
A wire harness is a group of wires, cables, and connectors bundled and routed as one unit, so a system can be wired in one step instead of wire by wire. An electrical cable assembly is similar but usually built around a single cable with connectors on each end. Both carry power and signals between the parts of a system.
Why build quality matters
Why build quality matters
Most harness failures start small: a drifting crimp, a gap in a shield termination, a bend that fatigues over time. We build to IPC/WHMA-A-620 Class 3 under our AS9100D quality system, and every assembly gets 100% continuity and Hipot testing before it ships. Prime contractors and Tier 1/2 suppliers rely on us for programs including the MQ-4C Triton and the B-52.
Most harness failures start small: a drifting crimp, a gap in a shield termination, a bend that fatigues over time. We build to IPC/WHMA-A-620 Class 3 under our AS9100D quality system, and every assembly gets 100% continuity and Hipot testing before it ships. Prime contractors and Tier 1/2 suppliers rely on us for programs including the MQ-4C Triton and the B-52.
IPC/WHMA-A-620 Class 3
IPC/WHMA-A-620 Class 3
AS9100D
AS9100D
100% Continuity Testing
100% Continuity Testing
Hipot Testing
Hipot Testing

Where wire harnesses are used.
Where wire harnesses are used.
Aerospace & Defense
Aerospace & Defense
Multi-branch harnesses for airframes, avionics, and ground systems.
Multi-branch harnesses for airframes, avionics, and ground systems.
Automotive & Transportation
Automotive & Transportation
High-voltage harnesses for battery, charging, and drive systems.
High-voltage harnesses for battery, charging, and drive systems.
Industrial Automation & Robotics
Industrial Automation & Robotics
Control cabinet harnesses and continuous-motion assemblies.
Control cabinet harnesses and continuous-motion assemblies.
How we build harnesses.
How we build harnesses.
Designed around the operating environment
Designed around the operating environment
Vibration, thermal range, and EMI requirements shape routing and material choices from the first design review.
Vibration, thermal range, and EMI requirements shape routing and material choices from the first design review.
ITAR and AS9100D as standard
ITAR and AS9100D as standard
Controlled handling of technical data and an AS9100D quality system on every build.
Controlled handling of technical data and an AS9100D quality system on every build.
Build records you can audit
Build records you can audit
Material lots and inspection records tied to each harness, ready for source inspection and customer audits.
Material lots and inspection records tied to each harness, ready for source inspection and customer audits.
First article to production
First article to production
The technicians who build your first article carry the design into recurring production, so the knowledge stays with the build.
The technicians who build your first article carry the design into recurring production, so the knowledge stays with the build.
Technical details.
Technical details.
For engineers: the key specs at a glance. Send your drawing or spec and we’ll confirm fit.
For engineers: the key specs at a glance. Send your drawing or spec and we’ll confirm fit.
Workmanship
Workmanship
IPC/WHMA-A-620, including Class 3 (the highest acceptance class).
IPC/WHMA-A-620, including Class 3 (the highest acceptance class).
Testing
Testing
100% continuity and Hipot (a high-voltage test that proves the insulation holds) on every assembly.
100% continuity and Hipot (a high-voltage test that proves the insulation holds) on every assembly.
Connector families
Connector families
MIL-spec, circular, rectangular and high-density, modular and data, and terminal and board-level connectors.
MIL-spec, circular, rectangular and high-density, modular and data, and terminal and board-level connectors.
Wire gauges
Wire gauges
32 AWG through 2/0 AWG.
32 AWG through 2/0 AWG.
High-speed data
High-speed data
Controlled impedance and pair geometry for Ethernet and high-speed data links.
Controlled impedance and pair geometry for Ethernet and high-speed data links.
Quality
Quality
AS9100D and ISO 9001:2015 quality systems, ITAR registered.
AS9100D and ISO 9001:2015 quality systems, ITAR registered.
Lengths & volumes
Lengths & volumes
Prototype through high-volume production, including assemblies with wire runs over 100 meters.
Prototype through high-volume production, including assemblies with wire runs over 100 meters.
Documentation
Documentation
Material lots and inspection records tied to each harness.
Material lots and inspection records tied to each harness.
Common questions
Common questions
Can you build to my drawing?
Can you build to my drawing?
Can you build to my drawing?
Yes. We build to your drawings and specifications, and we flag manufacturability concerns before they reach production.
Yes. We build to your drawings and specifications, and we flag manufacturability concerns before they reach production.
What’s the difference between Class 2 and Class 3?
What’s the difference between Class 2 and Class 3?
What’s the difference between Class 2 and Class 3?
They’re workmanship classes in IPC/WHMA-A-620. Class 3 has the tightest acceptance criteria and is used where failure isn’t acceptable, such as aerospace and defense. Class 2 covers products where long, reliable service is expected but not critical.
They’re workmanship classes in IPC/WHMA-A-620. Class 3 has the tightest acceptance criteria and is used where failure isn’t acceptable, such as aerospace and defense. Class 2 covers products where long, reliable service is expected but not critical.
Do you make prototypes and small quantities?
Do you make prototypes and small quantities?
Do you make prototypes and small quantities?
Yes. Prototype and low-volume builds are a routine part of our work, and the same engineering and inspection discipline applies from the first article onward.
Yes. Prototype and low-volume builds are a routine part of our work, and the same engineering and inspection discipline applies from the first article onward.
What should I send for a quote?
What should I send for a quote?
What should I send for a quote?
Drawings, a wire list, or a sketch, plus a description of the operating environment. An engineer reviews it and follows up with any questions.
Drawings, a wire list, or a sketch, plus a description of the operating environment. An engineer reviews it and follows up with any questions.
