Close-up of an overmolded cable assembly connector

Overmolded cable assemblies

Overmolded cable assemblies

Cables where the connector end is sealed inside molded plastic or rubber, so it resists pulling, bending, and water.

Cables where the connector end is sealed inside molded plastic or rubber, so it resists pulling, bending, and water.

What is an overmolded cable assembly?

What is an overmolded cable assembly?

Overmolding means molding plastic or rubber directly over the point where a cable meets its connector. It seals out water and dirt and stops the wires from breaking when the cable is pulled or bent, turning the cable, connector, and seal into one solid part.

Overmolding means molding plastic or rubber directly over the point where a cable meets its connector. It seals out water and dirt and stops the wires from breaking when the cable is pulled or bent, turning the cable, connector, and seal into one solid part.

Why build quality matters

Why build quality matters

Material selection, connector geometry, and strain relief design all determine whether an overmolded assembly survives its service environment or fails at the mold line. We engineer each overmold around the mechanical and thermal requirements of the application, from vibration resistance to environmental sealing.

Material selection, connector geometry, and strain relief design all determine whether an overmolded assembly survives its service environment or fails at the mold line. We engineer each overmold around the mechanical and thermal requirements of the application, from vibration resistance to environmental sealing.

Custom Tooling

Custom Tooling

Environmental Sealing

Environmental Sealing

Strain Relief Design

Strain Relief Design

AS9100D

AS9100D

Molded twist-lock power cord assembly

How we build overmolded assemblies.

How we build overmolded assemblies.

Mold and harness designed together

Mold and harness designed together

Connector geometry, cable jacket, and mold compound are chosen as one system, so the bond holds.

Connector geometry, cable jacket, and mold compound are chosen as one system, so the bond holds.

Tooling built for your part

Tooling built for your part

Mold tooling developed for your connector and cable, sized for prototype quantities and production runs.

Mold tooling developed for your connector and cable, sized for prototype quantities and production runs.

Sealed for your environment

Sealed for your environment

Washdown, outdoor, and immersion requirements drive compound selection and seal design from the start.

Washdown, outdoor, and immersion requirements drive compound selection and seal design from the start.

Repeatable from the first shot

Repeatable from the first shot

Controlled process parameters keep coverage, wall thickness, and finish consistent from lot to lot.

Controlled process parameters keep coverage, wall thickness, and finish consistent from lot to lot.

Technical details.

Technical details.

For engineers: the key specs at a glance. Send your drawing or spec and we’ll confirm fit.

For engineers: the key specs at a glance. Send your drawing or spec and we’ll confirm fit.

Process

Process

High-pressure injection molding with controlled process parameters for consistent, void-free coverage.

Automated dispensing with controlled curing for consistent, void-free coverage.

Tooling

Tooling

Custom mold tooling for your connector and cable, for prototype quantities and production runs.

Custom mold tooling for your connector and cable, for prototype quantities and production runs.

Materials

Materials

High-pressure injection overmolding in PVC, polyurethane (TPU), and thermoplastic elastomers (TPE). Two-part potting in epoxy, polyurethane, and silicone compounds.

High-pressure injection overmolding in PVC, polyurethane (TPU), and thermoplastic elastomers (TPE). Two-part potting in epoxy, polyurethane, and silicone compounds.

Sealing

Sealing

Options for splash, washdown, outdoor use, and immersion.

Options for splash, washdown, outdoor use, and immersion.

Ingress rating

Ingress rating

IP67 and IP68 options, depending on assembly design and application requirements.

IP67 and IP68 options, depending on assembly design and application requirements.

Testing

Testing

Post-mold inspection for voids and coverage, plus bending, twisting, and vibration cycles on prototypes.

Post-mold inspection for voids and coverage, plus bending, twisting, and vibration cycles on prototypes.

Quality

Quality

IPC/WHMA-A-620 workmanship, AS9100D and ISO 9001:2015 quality systems, ITAR registered.

IPC/WHMA-A-620 workmanship, AS9100D and ISO 9001:2015 quality systems.

Volumes

Volumes

Prototype through production.

Prototype through production.

Common questions

Common questions

Overmolding or a backshell: which is better?

Overmolding or a backshell: which is better?

Overmolding or a backshell: which is better?

Overmolding seals the connector and cable into one part, which is best for moisture, flexing, and handling. A backshell is a separate hard cover that can be opened and serviced. We’ll recommend one based on your environment.

Overmolding seals the connector and cable into one part, which is best for moisture, flexing, and handling. A backshell is a separate hard cover that can be opened and serviced. We’ll recommend one based on your environment.

Do I need custom tooling?

Do I need custom tooling?

Do I need custom tooling?

Usually, yes. We develop mold tooling for your connector and cable, sized for both prototype quantities and production runs.

Usually, yes. We develop mold tooling for your connector and cable, sized for both prototype quantities and production runs.

Can you build to my drawing?

Can you build to my drawing?

Can you build to my drawing?

Yes. We build to your drawings and specifications, and we flag manufacturability concerns before they reach production.

Yes. We build to your drawings and specifications, and we flag manufacturability concerns before they reach production.

What should I send for a quote?

What should I send for a quote?

What should I send for a quote?

Drawings, a wire list, or a sketch, plus a description of the operating environment. An engineer reviews it and follows up with any questions.

Drawings, a wire list, or a sketch, plus a description of the operating environment. An engineer reviews it and follows up with any questions.

Ready to spec an overmolded assembly?

Ready to spec an overmolded assembly?